EXPANSION JOINT

1 of 2 MATERIAL ORDERING DATA Any specification that is referenced in this Material Order Data sheet is required to be to the latest revision at time of award. IDN: N4523A 6093-1220 ICN: 38WAI25603 KO: S01 KOI: 002 Paragraph 4 Ordering Data ASTM-F-1123, (46 INCH) STANDARD SPECIFICATION FOR NON-METALLIC EXPANSION JOINTS, dated 31 DECEMBER 1987 (Reapproved 2024) (From ASTM-F1123) 4.1 Orders for products under this specification shall include the following information: 4.1.1 Inside diameter of connecting pipes (joint ID): 46” 4.1.2 Face-to-face dimension that is the flange-to-flange dimension into which the expansion joint is to be installed: 12” dia. ± 3/16” 4.1.3 Maximum and minimum operating pressure in pounds-force per square inch gage (pascals): 21 psig min. 40 psig max. 4.1.4 Maximum and minimum operating temperature in °F (°C): 60°F min. 105°F max. 4.1.5 Flange drilling in accordance with the appendix titled “Common Flange Dimension/Drilling Chart’’ of the Technical Handbook on Rubber Expansion Joints and Flexible Pipe Connectors (herein referred to as the Technical Handbook) or in accordance with special customer requirements. Drill ONE flange only as follows: 46” Dia. Expansion joint w/retaining rings. Quantity required: 1 EA. Bolt Circle Dia. = 52 ± 5/16” Bolt Holes = 42ea. @ 1-5/16” dia. ± 1/64” 4.1.6 Fluid to be handled: SEAWATER 4.1.7 This ASTM specification designation: ASTM F1123-87 (R 2024) 4.1.8 Movement data requirements (including shock or vibratory excursions if applicable): N/A 4.1.9 Design certification burst test if required (see 9.1): N/A 4.1.10 Hydrostatic or special tests if required (see 9.2): Required PSIG: 60 -- 1 of 10 -- 2 of 2 4.1.11 Certification of expansion joint if required (see Section 12): N/A 4.1.12 Certified detailed drawing of the expansion joint if required (see 12.2): N/A Additional Data requirements: Must meet Grade A shock requirements. MANUFACTURED DATE NOT TO BE PRIOR TO 4Q2022 All unit, intermediate, and shipping containers must be marked in accordance with MIL-STD-129. Refer to DLA Procurement Note C20 for further instructions. Prepared By: Matthew Warren Code: 260.9 -- 2 of 10 -- 1 of 2 MATERIAL ORDERING DATA Any specification that is referenced in this Material Order Data sheet is required to be to the latest revision at time of award. IDN: N4523A 6093-1222 ICN: 38WAI25604 KO: S01 KOI: 002 Paragraph 4 Ordering Data ASTM-F-1123, (46 INCH) STANDARD SPECIFICATION FOR NON-METALLIC EXPANSION JOINTS, dated 31 DECEMBER 1987 (Reapproved 2024) (From ASTM-F1123) 4.1 Orders for products under this specification shall include the following information: 4.1.1 Inside diameter of connecting pipes (joint ID): 46” 4.1.2 Face-to-face dimension that is the flange-to-flange dimension into which the expansion joint is to be installed: 12” dia. ± 3/16” 4.1.3 Maximum and minimum operating pressure in pounds-force per square inch gage (pascals): 21 psig min. 40 psig max. 4.1.4 Maximum and minimum operating temperature in °F (°C): 60°F min. 105°F max. 4.1.5 Flange drilling in accordance with the appendix titled “Common Flange Dimension/Drilling Chart’’ of the Technical Handbook on Rubber Expansion Joints and Flexible Pipe Connectors (herein referred to as the Technical Handbook) or in accordance with special customer requirements. Drill ONE flange only as follows: 46” Dia. Expansion joint w/retaining rings. Quantity required: 1 EA. Bolt Circle Dia. = 52 ± 5/16” Bolt Holes = 42ea. @ 1-5/16” dia. ± 1/64” 4.1.6 Fluid to be handled: SEAWATER 4.1.7 This ASTM specification designation: ASTM F1123-87 (R 2024) 4.1.8 Movement data requirements (including shock or vibratory excursions if applicable): N/A 4.1.9 Design certification burst test if required (see 9.1): N/A 4.1.10 Hydrostatic or special tests if required (see 9.2): Required PSIG: 60 -- 3 of 10 -- 2 of 2 4.1.11 Certification of expansion joint if required (see Section 12): N/A 4.1.12 Certified detailed drawing of the expansion joint if required (see 12.2): N/A Additional Data requirements: Must meet Grade A shock requirements. MANUFACTURE DATE NOT TO BE PRIOR TO 4Q 2022. All unit, intermediate, and shipping containers must be marked in accordance with MIL-STD-129. Refer to DLA Procurement Note C20 for further instructions. Prepared By: Matthew Warren Code: 260.9 -- 4 of 10 -- 1 of 2 MATERIAL ORDERING DATA Any specification that is referenced in this Material Order Data sheet is required to be to the latest revision at time of award. IDN: N4523A 6093-1223 ICN: 38WAI25604 KO: S01 KOI: 001 Paragraph 4 Ordering Data ASTM-F-1123, (28 INCH) STANDARD SPECIFICATION FOR NON-METALLIC EXPANSION JOINTS, dated 31 DECEMBER 1987 (Reapproved 2024) (From ASTM-F1123) 4.1 Orders for products under this specification shall include the following information: 4.1.1 Inside diameter of connecting pipes (joint ID): 28” 4.1.2 Face-to-face dimension that is the flange-to-flange dimension into which the expansion joint is to be installed: 12 Dia. ± 3/16 4.1.3 Maximum and minimum operating pressure in pounds-force per square inch gage (pascals): 21 psig min. 40 psig max. 4.1.4 Maximum and minimum operating temperature in °F (°C): 60°F min. 105°F max. 4.1.5 Flange drilling in accordance with the appendix titled “Common Flange Dimension/Drilling Chart’’ of the Technical Handbook on Rubber Expansion Joints and Flexible Pipe Connectors (herein referred to as the Technical Handbook) or in accordance with special customer requirements. Drill ONE flange only as follows: 28” Dia. Expansion joint w/retaining rings. Quantity Required: 1 ea. Bolt Circle Dia. = 32-7/16” ± 5/16” Bolt Holes = 32ea. @ 1-3/16” dia. ± 1/64” 4.1.6 Fluid to be handled: Seawater 4.1.7 This ASTM specification designation: ASTM F1123-87 (2024) 4.1.8 Movement data requirements (including shock or vibratory excursions if applicable): N/A 4.1.9 Design certification burst test if required (see 9.1): N/A 4.1.10 Hydrostatic or special tests if required (see 9.2): Required PSIG: 6…