FAS-34 Overhaul

Ship/HULL NO. Ship/HULL NAME ICN: Rev: Key Op: FAS-34 COMFLEACT SASEBO OPS JON: N6105826PRPR934 A01 TITLE: 25UB1308 Boat (FAS-34); repair/preserve JOB SPECIFICATION Anticipated Award Date: Production Completion Date: POP Start Date: POP End Date: PREPARED BY: CODE T.SATO H ST APPROVED BY: �41/l CODE $.MURAKAMI S225 CONCURRED BY: S.MOROOKA ASSIST PLANNER'S NAME: D.AKAMINE ASSIST PLANNER'S NAME: ASSIST PLANNER'S NAME: DESCRIPTION: JSN(S): 2024OPS009 S/F CONTACT: M.KAWABATA / MMC TRAN, AN.T Approved by S300/S900 Work Completed S/Force: Rate: Ship Supt: Date: WORK CERTIFICATION SIGNATURES COMPLETION OF WORK REVIEW: AJ� CODE S231 , CODE E AK CODE CODE CASREP# CWP# Date: Date: SRF CONTROL NO.: BADGE NO.: SHOP/CODE: PREPARING ACTIVITY: SASEBO DATE 3/29/2024 CCNS# Avl: FY24 LWC: PHONE: DATE: 06/09/2026 08/01/2026 09/01/2026 11/30/2026 12/15/2026 -- 1 of 8 -- Shin/HULL NO. Ship/HULL NAME ICN: Rev: Key Op: FAS-34 COMFLEACT SASEBO OPS JON: N6105826PRPR934 A01 TITLE: 25UB1308 Boat (FAS-34); repair/preserve 1. SCOPE: 1.1 Title: 25UB1308 Boat (FAS-34); repair/preserve 1.2 Location of Work: 1.2.1 Contractor's yard 1.3 Identification: Quantity (One), 25UB1308 Utility Boat, Principal Dimension as Follows Manufacturer Length Over All Beam with RUB Rail Height Light Ship Weight Installed Power METAL SHARK, LLC. 27 Feet - 5 Inch 8 Feet - 6 Inch 9 Feet - 9 Inch 5,537 Pound 230 HP 1.3.1 A Total of (4 SF) of Bow Plate, 3/16 Inch Thickness Aluminum Alloy 1.3.2 Quantity (One AY), AFT Curtain (Size: 48 Inch Width by 78 Inch Height) for Cabin Access 1.3.3 Quantity (One EA), Seat in Front of Cabin 1.3.4 A Total of (55 LF) of Rubber Fender (4-1/2 Inch Height) on Hull 1.3.5 Quantity (2 EA), Windshield Wiper and Motor, P/N: 539324 and 30991 1.3.6 Quantity (One EA), Zinc Anode on Transom 1.3.7 A Total of (580 SF) of Preservation Area of Aluminum Alloy Boat for Underwater Hull, Freeboard, Cabin, Bulwark, Main Deck, Engine Guard, Tow Post Safety Screen and Deck Fitting 1.3.8 A Total of (220 SF) of Preservation Area of Aluminum Alloy Boat for Structure Member, Main Deck, Bulwark, Transom and Step for Nonskid (Peel and Stick) Deck Covering 1.3.9 A Total of (170 SF) of Nonskid (Peel and Stick) Deck Covering on Main Deck, Top of Bulwark, Top of Generator/Engine Starting Battery Compartment and Step 2, REFERENCES: 2.1 2.2 Standard Items (FY26) 25C-100-001, General Arrangement Outboard Profile -- 2 of 8 -- Shio/HULL NO. Shio/HULL NAME JON: ICN: Rev: Key Op: FAS-34 COMFLEACT SASEBO OPS N6105826PRPR934 TITLE: 25UB1308 Boat (FAS-34); repair/preserve 2.3 25C-100-002, Hull Lines 2.4 25C-100-003, Hull Structure 2.5 25C-150-001, Console 2.6 25C-l 70-001, Doors and Hatches 2.7 25C-180-001, Engine Guard 2.8 25C-200-001, Propulsion Equipment 2.9 25C-560-001, Steering System 2.10 25C-580-001, AFT Tow Post 2.11 25C-580-002, AFT Tow Post Safety Screen 2.12 25C-600-001, Dive Door 2 .13 25C-610-001, Hoisting Fittings 2.14 25C-630-001, Cleats and Handrails 2.15 25C-300-001, DC Electrical Schematic 2.16 25C-300-002, DC Electrical Components 2.17 25C-400-001, Dash Arrangement 2.18 803-0921865, Cathodic Protection, Hull Zinc Protection 2.19 MIL-STD-2003B, Electric Plant Installation Standard Methods for Surface Ship.s and Submarines A01 2.20 MIL-STD-1310H(NAVY), Shipboard Bonding, Grounding, and Other Techniques for Electromagnetic Compatibility, Electromagnetic Pulse (EMP) Mitigation, and Safety 2.21 0900-LP-060-4010 Chg-2, Fabrication, Welding and Inspection of Metal Boat and Craft Hulls 3. REQUIREMENTS: 3.1 Hoist and set the boat listed in 1.3 on the blocks (either in land or a barge) in contractor's yard to accomplish repair and preservation work. 3.1.1 Im.mediately after the boat has been set on the blocks, remove marine growth and clean entire underwater hull using fresh water. -- 3 of 8 -- Shio/HULL NO. Shio/HULL NAME ICN: Rev: Key Op: JON:FAS-34 COMFLEACT SASEBO OPS N6105826PRPR934 A01 TITLE: 25UB1308 Boat (FAS-34); repair/preserve 3.1.2 Bounce the boat necessary to preserve the underwater hull. 3.1.3 Remove each existing zinc anode listed in 1.3.6 for preservation work, using ENCLOSURE (Al for guidance. 3.1.4 Disconnect mechanically and remove each electrical cable from foundation and cable hanger to facilitate preservation work and install the same upon completion of preservation work. 3.1.5 Upon completion of repair and preservation work, and after approval of CFAS PORT OPERATION, lower or return the boat onto water. 3.2 Remove each damaged section, fabricate and install each new plate listed in 1.3.1 out of new 0.1875 inch thick aluminum alloy plate AL5086 H116 conforming to ASTM 8928, using 2.2 through 2.4 for guidance. (I) "VISUAL" 3.2.1 Accomplish the requirements of 2.21 including Sections 6 through 8 for welding and visual (VT) inspection using 5X magnifying glass. (I) (G) "PT" 3.2.1.1 Accomplish liquid penetrant (PT) inspection in accordance with Sections 6 through 8 of 2.21. -S130 (See NOTE 4.2) 3.3 Accomplish the requirements for repair of miscellaneous equipment of the boat listed in 1.3 as follows, using 2.2 through 2.14 and ENCLOSURE (A) for guidance. 3.3.1 Remove each existing, template from existing, fabricate and install new curtain listed in 1.3.2 out of each new marine fabric or Equal with each new fastener. 3.3.2 Remove each existing and re-upholster seat listed in 1.3.3 out of new artificial leather conforming to A-A-59517 Class One or Equal with cushion. 3.3.3 Remove each existing, fabricate and install new rubber fender listed in 1.3.4 out of new rubber sheet conforming to MIL-PRF-900 with each new fastener and existing retainer plate. 3.3.3.1 Clean each existing surface of retainer plate. 3.3.4 Remove each existing and install new windshield wiper and motor listed in 1.3.5, using 2.15 through 2.17 for guidance. 3.3.4.1 Adjust and align each arm and blade of each new windshield wiper. 3.3.4.2 Connect and verify connections. -- 4 of 8 -- Shin/HULL NO. Shin/HULL NAME I ICN: JON: N6105826PRPR934 Rev: Key Op…