USCGC Hudson Boat Handling Equipment Inspection

USCGC HUDSON (WLIC 801) SPECIFICATION FOR DOCKSIDE REPAIRS FY2026 Developed By: Erik C Elasik (Rev-0, 15 October 2025) -- 1 of 14 -- USCGC HUDSON (WLIC-160A) DOCKSIDE AVAILABILITY FY2026 35 (Rev-0) 25903_ESD_0924_FLT REC_25903_FLT_160 WLIC ‘A’ Class (ALL) (0323) WORK ITEM 7: Hull Fittings, Weight Handling Rigging Hardware, Inspect and Test 1. SCOPE 1.1 Intent. This work item describes the requirements for the Contractor to inspect and test designated hull fittings, listed in Table 1. TABLE 1 - DESIGNATED ATON HULL FITTINGS QTY DESCRIPTION LOCATION 3 Pad Eye, 1-1/4” Main Deck, Frame -1, P/S and CL 4 Pad Eye, 1-1/4” Main Deck, Frame 11, P/S 2 Pad Eye, 1-1/4” Main Deck, Frame 17, P/S 2 Pad Eye, 1-1/4” Main Deck, Frame 20, P/S 4 Pad Eye, 1-1/4” Main Deck, Frame 22, P/S 4 Pad Eye, 1-1/4” Main Deck, Frame 49, P/S 2 Pad Eye, 1-1/4” Main Deck, Frame 79, P/S 1.2 Government-furnished property. None. 2. REFERENCES COAST GUARD DRAWINGS Coast Guard Drawing FL 1204-3, Rev A, Welded Padeyes & Links COAST GUARD PUBLICATIONS Surface Forces Logistics Center Standard Specification 0000 (SFLC Std Spec 0000), 2020, General Requirements Surface Forces Logistics Center Standard Specification 0740 (SFLC Std Spec 0740), 2020, Welding and Allied Processes Surface Forces Logistics Center Standard Specification 6310 (SFLC Std Spec 6310), 2020, Requirements for Preservation of Ship Structures OTHER REFERENCES None -- 2 of 14 -- USCGC HUDSON (WLIC-160A) DOCKSIDE AVAILABILITY FY2026 36 (Rev-0) 3. REQUIREMENTS 3.1 General. 3.1.1 CIR. None. 3.1.2 Tech Rep. Not applicable. 3.1.3 Protective measures - general. The Contractor shall furnish and install all protective coverings to seal off and protect all non-affected vessel's components, equipment, and spaces in the vicinity of the work area against contamination during the performance of work. Upon completion of work, the Contractor shall remove all installed protective measures, inspect for the presence of contamination, and return all contaminated equipment, components, and spaces to original condition of cleanliness. 3.1.4 Interferences. The Contractor shall handle all interferences in accordance with SFLC Std Spec 0000, paragraph 3.3.5 (Interferences). 3.2 Inspection and test particulars. The Contractor shall accomplish the following inspections for all designated fittings, and submit a CFR. 3.2.1 Visual. Perform a visual inspection of fitting structures and associated foundations, for evidence of fractures, excessive wear, deformation, and corrosion. 3.2.2 NDE. Structurally inspect all fittings, including foundation welds, by NDE methods in accordance with SFLC Std Spec 0740, Appendix C. If a NDE method that requires coating removal is selected, perform subsequent touch-up preservation in accordance with SFLC Std Spec 6310, paragraph 3.1.13 (Touch-ups and minor coating repairs). NOTE Common NDE methods not requiring coating removal include, but are not limited to: a. Radiographic Testing (RT). b. Ultrasonic Testing (UT). c. Eddy Current Testing (ET). 3.2.3 Measurements. Measure and record each pad-eye diameter (“A” dimension), shown on Coast Guard Drawing FL 1204-3 as guidance. 3.2.4 Pull-test. In lieu of NDE, the Contractor may pull-test all pad eyes in accordance with SFLC Std Spec 5000, paragraph 3.2.7 (Pull-Test), using the working load provided in Coast Guard Drawing FL 1204-3 for each designated pad eye size. Visually inspect all welds for signs of damage, after completion of pull-test. -- 3 of 14 -- USCGC HUDSON (WLIC-160A) DOCKSIDE AVAILABILITY FY2026 37 (Rev-0) 4. NOTES This section is not applicable to this work item. -- 4 of 14 -- USCGC HUDSON (WLIC-160A) DOCKSIDE AVAILABILITY FY2026 38 (Rev-0) 57300_XdckWnchInspctSrvc_ACC_0121_IBCT REC_57300_XdckWnch_IBCT_160 WLIC (ALL) (1014) WORK ITEM 8: Crossdeck Winch, Inspect & Service 1. SCOPE 1.1 Intent. This work item describes the requirements for the Contractor to inspect and service the Utility Air Winch Model HU-40 Series. 1.2 Government-furnished property. None. 2. REFERENCES COAST GUARD DRAWINGS Coast Guard Fleet Drawing FL-1112-18, Rev -, HU40 Series Spud Winch Foundation COAST GUARD PUBLICATIONS Coast Guard Technical Publication (TP) 4958, Section A, Amendment 1; Mar 2011, Utility Air Winch Model HU-40 Series Surface Forces Logistics Center Standard Specification 0000 (SFLC Std Spec 0000), 2020, General Requirements Surface Forces Logistics Center Standard Specification 5000 (SFLC Std Spec 5000), 2020, Auxiliary Machine Systems OTHER REFERENCES None 3. REQUIREMENTS 3.1 General. 3.1.1 CIR. None. 3.1.2 Tech Rep. Not applicable. -- 5 of 14 -- USCGC HUDSON (WLIC-160A) DOCKSIDE AVAILABILITY FY2026 39 (Rev-0) 3.1.3 Protective measures. The Contractor must furnish and install all protective measures in accordance with SFLC Std Spec 0000, paragraph 3.3.3 (Vessel component, space, and equipment protection). 3.1.4 Interferences. The Contractor must handle all interferences in accordance with SFLC Std Spec 0000, paragraph 3.3.5 (Interferences). 3.2 Renewal task particulars. The Contractor must perform the tasks designated in Table 1 below, in accordance with SFLC Std Spec 5000: TABLE 1 – REQUIRED TASKS ADDITION REQUIREMENTS # TASK TYPE (SFLC STD SPEC 5000 PARA. REF.) QTY COMPONENT OR ASSEMBLY APPENDIX AND PARA. FROM SFLC STD SPEC 5000 OTHER 1 Operate and Inspect 6 3.2.1 (Operate and Inspect) D2.1 (Fastener assemblies) D2.1 (Fastener assemblies) Submit CFR. 2 NDE and Preserve 6 Winch Foundation 3.2.4 (Preservation) 3.2.5 (NDE) 1. Finish coat color: black (17038). 2. Areas to NDE: …- All weld joints connecting winch foundations to the deck …- Winch feet 3. Submit CFR. 3 Renew 6 Wire Rope Assembly D2.2 (Wire Rope Assemblies) Wire rope particulars: Each set is as follows: - Nominal diameter: 5/8 inch. - Nominal strength: 6x37 XXIPS IWRC RRL - Length of rope required: 150 ft per assembly - End fitting type: Poured spelter or fiege 4 Groom and Lubricate 6 Winch 3.2.6 (Groom and lubr…