BAND SAW

DLA MARITIME NORFOLK – CONTRACTING DIVISON PORTSMOUTH, VA 23709-5000 This is a COMBINED SYNOPSIS/SOLICITATION for commercial items prepared in accordance with the information in Federal Acquisition Regulation (FAR) Part 13 using Simplified Acquisition Procedures (SAP). This requirement will be solicited as Brand Name AMADA or equivalent. This announcement constitutes the only solicitation; a written solicitation will not be issued. PAPER COPIES OF THIS SOLICITATION WILL NOT BE AVAILABLE. This combined synopsis/solicitation WILL be posted to SAM at https://sam.gov. RFQ NUMBER: N42158-61460151 BUYER: MELISSA LANGLEY EMAIL ADDRESS: MELISSA.LANGLEY@DLA.ML This solicitation documents and incorporates provisions and clauses in effect though FAC 2026-01 and the DFARS Change notice 5/7/2026. It is the responsibility of the contractor to be familiar with the applicable clauses and provisions. The clauses may be accessed in full text at this website: https://www.acquisition.gov/. NNSY - Norfolk Naval Shipyard requests responses from qualified sources capable of providing the material that is referenced below. All items shall be new. No refurbished or used items will be accepted. This solicitation is set aside for a small business. REQUIREMENT DESCRIPTION TABLE CLIN NUMBER DESCRIPTION QUANTITY UNIT PRICE TOTAL 0001- 61460151 VERTICAL TILT FRAME BANDSAW (AMADA VT4555M OR EQUIVALENT) 1 (EA) Statement Of Specification for the Procurement of a Vertical Tilt-Frame Bandsaw 1. SCOPE: This Specifications defines the requirements for one each (1 ea.) VERTICAL Tilt- Frame Metal cutting Band Saw. 2. DESCRIPTION: The equipment shall consist of one each (1 ea.) Vertical Tilt-Frame bandsaw (Amada VT4555M or equivalent) that meets a minimum of the following requirements. 2.1. DESIGN: The machine shall be new and unused, capable of performing its intended function. The machine shall be complete, so that when connected to the utilities identified herein, it can be used for any function for which it is designed and constructed. 2.2. WORKTABLE: The machine shall be equipped with a T-slotted worktable that has a Work area of 24.25” x 33” a Table height of 38” and two machined T-slots. 2.3. ELECTRICAL DESIGN: The entire electrical system shall conform to the requirements below and NFPA '79. All machine components shall use a single electrical source. 2.4. WORK LIGHT: The equipment shall include a work light to illuminate the work envelope. The lighting shall comply with NFPA 79 requirements and have a protective shield. Fluorescent or other lighting with a strobe effect is not acceptable. -- 1 of 67 -- 2.5. CONTROLS: Operator controls, instrumentation and indicators shall be mounted convenient to operating personnel. Such devices shall be clearly and legibly marked for function and identification. Controls shall be fitted with suitable handles, push buttons, or control knobs, as applicable. Controls shall be provided with an IEC fused disconnect switch and magnetic motor starters with overload and low-voltage protection. Power supply shall provide low voltage (24 volts DC) control to all push buttons at operator’s control panel and machine lighting circuits. The PLC control and drives shall be mounted in a moisture-tight compartment with vibration isolation mounting. 2.6. FRONT MOUNTED SPEED CONTROL: Machine shall be equipped with Front- Mounted Speed Control that allows blade speed to be adjusted from operator’s control station. 2.7. ELECTRICAL EQUIPMENT: All Electrical Equipment shall conform to National Electrical Code NFPA 79 and The Electrical Control Panel shall be U.L. Labeled. 1.1. SAFETY SIGNS AND LABELS: Safety signs and labels shall be in accordance with NEMA Z535.4. Safety signs and labels shall be securely attached to the equipment in visible locations, at the point of hazard(s), with any safety precautions to be observed by the operator or maintenance personnel permanently marked on the signs. 1.2. BAND WHEELS: Band wheels shall be manufactured from cast iron with a diameter no less than 19”. 1.3. MITER CUTTING: Column and blade shall tilt up to 60° right and left of vertical with work always stationery. 1.4. SAW FEED STOPS: Machine shall be equipped with Adjustable stops can be pre-set to stop advance of the saw head and return of blade and to stop motor at any location within the 18” (457 mm) travel of the blade. 1.5. WORK HOLDING VISE: Vise shall meet a minimum of the following requirements. a) Maximum opening 18” (minimum) b) Jaws designed to be shifted to either right or left side of blade c) Jaws shall be 6” high and 12” wide. 1.6. SAFETY GUARDING: Covers, guards, or other safety devices shall be provided per ANSI B11.22 and 29 CFR 1910. The safety devices shall not interfere with the operation of the machine. The safety devices shall prevent unintentional contact with the guarded part, and shall be removable to facilitate inspection, maintenance, and repair of the parts. 1.7. COOLANT SYSTEM: Machine shall be provided with a 21-gallon flood coolant system controlled by on-off selector switch at operator’s station. 1.8. GUIDE SYSTEM: upper and lower guides shall be equipped with preloaded carbide faced back-up blocks to support the back edge of the blade. 1.9. INTERCHANGEABILITY: All parts subject to replacement shall be manufactured to definite dimensions and tolerances. Replacement parts shall be interchangeable without requiring modification. 1.10. LUBRICATION: Bearings (except sealed-for-life and self-lubricating type), mating gears and sliding parts shall be provided with means for lubrication. Reservoirs -- 2 of 67 -- of splash-type systems shall be fitted with oil level sight gauges. Automatic force-feed and manually operated force feed systems shall be supplied with a filter. Manually operated systems shall have control handles mounted in an accessible location convenient to the operator. Oil holes, grease fittings and filler caps shall be easily accessible. 2. REQUIREMENTS: The machi…