Buckle and Clips, End Strap, Gold Finish, MC

DISTRIBUTION STATEMENT A. Approved for public release, distribution unlimited. MIL-DTL-1963K 04 September 2019 SUPERSEDING MIL-B-1963J July 29, 1988 MILITARY SPECIFICATION BUCKLES; AND CLIPS, END, STRAP (FOR BELT, TROUSERS) This specification is approved for use by all Departments and Agencies of the Department of Defense (DoD). 1. SCOPE 1.1 Scope. This document is applicable to buckles and end clips used with belts worn by personnel of the United States military. 1.2 Classification. This specification covers the following types, classes, subclasses and sizes of buckles and clips. Type I - Buckle, closed front (see Figure 1) Sizes: 1-1/8 inch 1-5/16 inch Classes: Class 1 – Yellow brass Subclass A – Mirror finish, lacquer coated (see 3.5.2.1) Subclass B – Mirror finish, chromium plated (see 3.5.2.5.1) Subclass C – 24K gold plated (see 3.5.2.5.2) Class 2 – Nickel silver, matte finish (see 3.5.2.4) AMSC N/A FSC 8315 Comments, suggestions, or questions on this document should be addressed: Attn: DLA Troop Support, 700 Robbins Avenue, Philadelphia, PA 19111-5096. Since contact information can change, verify the currency of the address information using Acquisition Streamlining and Standardization Information System (ASSIST) online database https://assist.dla.mil. INCH-POUND Source: https://assist.dla.mil -- Downloaded: 2020-10-06T20:29Z Check the source to verify that this is the current version before use. -- 1 of 18 -- MIL-DTL-1963K 2 Type II - Buckle, open front Size - 1-1/4 inch (see Figure 2) Classes: Class 1 – Yellow brass, black oxidized finish (see 3.5.2.3) Class 2 – DELETED Size - 1-5/16 inch (see Figure 3) Class 3 – Red brass Subclass A – DELETED Subclass B - 24K gold plated (see 3.5.2.5.2) Subclass C – Antique oxidized, lacquer coated (see 3.5.2.2) Type III - Clip (see Figure 4) Sizes: 1 inch 1-1/4 inch Classes: Class 1 – Yellow brass Subclass A – Mirror finish, lacquer coated (see 3.5.2.1) Subclass B – Black oxidized finish (see 3.5.2.3) Subclass C – Mirror finish, chromium plated (see 3.5.2.5.1) Subclass D – 24K gold plated (see 3.5.2.5.2) Class 2 – Nickel silver, matte finish (see 3.5.2.4) Size - 1-1/4 inch Classes: Class 3 – Red brass Subclass A – Mirror finish, lacquer coated (see 3.5.2.1) Subclass B – Antique oxidized, lacquer coated (see 3.5.2.2) Class 4 – DELETED Subclass A – DELETED Subclass B – DELETED 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements of documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. Source: https://assist.dla.mil -- Downloaded: 2020-10-06T20:29Z Check the source to verify that this is the current version before use. -- 2 of 18 -- MIL-DTL-1963K 3 DEPARTMENT OF DEFENSE SPECIFICATIONS MIL-F-495 - Finish, Chemical, Black, for Copper Alloys MIL-DTL-833 - Belt, Trousers, Cotton Webbing, with Clip MIL-DTL-45204 - Gold Plating, Electrodeposited (Copies of these documents are available online at https://quicksearch.dla.mil.) 2.2.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation or contract. DRAWINGS U.S. ARMY NATICK RESEARCH, DEVELOPMENT AND ENGINEERING CENTER 2-4-57 - Buckles; and Clips, End, Strap (for Belt, Trousers); Type I, (Closed Front) Buckle Sizes 1-1/8” and 1-5/16”, Class 1 and 2 2-4-58 - Buckle and Clip, End, Strap (for Belt Trousers); Type III Clip, End, Strap, Sizes 1” and 1-1/4”, Class 1, 2, 3 and 4 2-4-63 - Buckle and Clip, End, Strap (for Belt, Trousers); Die Cut Card for Mounting End Clip 2-4-64 - Buckles: and Clips, End, Strap (for Belt, Trousers); Type II, (Open Front) Buckle, 1-5/16” Size, Class 3 4-1-436 - Buckles; and Clips, End, Strap (for Belt, Trousers); Type II, (Open Front) Buckle, 1-1/4 Inch Size, Class 1 and 2 (Copies of drawings are available from the U.S. Army Combat Capabilities Development Command Soldier Center, ATTN: FCDD-SCP-WC, 10 General Greene Avenue, Natick, MA 01760-5019.) OTHER GOVERNMENT DOCUMENTS AND PUBLICATIONS DEPARTMENT OF THE ARMY, THE INSTITUTE OF HERALDRY (TIOH) The Institute of Heraldry, Department of Defense Standard Metal Finish Chip Set (The standard chip(s) for color or finish may be obtained from the procuring activity for Government procurements.) 2.3 Non-Government publications. The following documents form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. Source: https://assist.dla.mil -- Downloaded: 2020-10-06T20:29Z Check the source to verify that this is the current version before use. -- 3 of 18 -- MIL-DTL-1963K 4 AMERICAN SOCIETY FOR QUALITY (ASQ) ASQ/ANSI Z1.4-2003 - Sampling Procedures and Tables for Inspection by Attributes (Copies are available online at https://asq.org.) ASTM INTERNATIONAL ASTM B36/B36M - Standard Specification for Brass Plate, Sheet, Strip, and Rolled Bar ASTM B122/B122M - Standard Specification for Copper-Nickel-Tin Alloy, Copper- Nickel-Zinc Alloy (Nickel Silver), and Copper-Nickel Alloy Plate, Sheet, Strip, and Rolled Bar ASTM B134/B134M - Standard Specification for Brass Wire ASTM B206/B206M - Standard Specification for Copper-Nickel…