USCGC Hudson Winch and Weight Handling Inspection

USCGC HUDSON (WLIC 801) SPECIFICATION FOR DOCKSIDE REPAIRS FY2026 Developed By: Erik C Elasik (Rev-0, 15 October 2025) -- 1 of 11 -- USCGC HUDSON (WLIC-160A) DOCKSIDE AVAILABILITY FY2026 38 (Rev-0) 57300_XdckWnchInspctSrvc_ACC_0121_IBCT REC_57300_XdckWnch_IBCT_160 WLIC (ALL) (1014) WORK ITEM 8: Crossdeck Winch, Inspect & Service 1. SCOPE 1.1 Intent. This work item describes the requirements for the Contractor to inspect and service the Utility Air Winch Model HU-40 Series. 1.2 Government-furnished property. None. 2. REFERENCES COAST GUARD DRAWINGS Coast Guard Fleet Drawing FL-1112-18, Rev -, HU40 Series Spud Winch Foundation COAST GUARD PUBLICATIONS Coast Guard Technical Publication (TP) 4958, Section A, Amendment 1; Mar 2011, Utility Air Winch Model HU-40 Series Surface Forces Logistics Center Standard Specification 0000 (SFLC Std Spec 0000), 2020, General Requirements Surface Forces Logistics Center Standard Specification 5000 (SFLC Std Spec 5000), 2020, Auxiliary Machine Systems OTHER REFERENCES None 3. REQUIREMENTS 3.1 General. 3.1.1 CIR. None. 3.1.2 Tech Rep. Not applicable. -- 2 of 11 -- USCGC HUDSON (WLIC-160A) DOCKSIDE AVAILABILITY FY2026 39 (Rev-0) 3.1.3 Protective measures. The Contractor must furnish and install all protective measures in accordance with SFLC Std Spec 0000, paragraph 3.3.3 (Vessel component, space, and equipment protection). 3.1.4 Interferences. The Contractor must handle all interferences in accordance with SFLC Std Spec 0000, paragraph 3.3.5 (Interferences). 3.2 Renewal task particulars. The Contractor must perform the tasks designated in Table 1 below, in accordance with SFLC Std Spec 5000: TABLE 1 – REQUIRED TASKS ADDITION REQUIREMENTS # TASK TYPE (SFLC STD SPEC 5000 PARA. REF.) QTY COMPONENT OR ASSEMBLY APPENDIX AND PARA. FROM SFLC STD SPEC 5000 OTHER 1 Operate and Inspect 6 3.2.1 (Operate and Inspect) D2.1 (Fastener assemblies) D2.1 (Fastener assemblies) Submit CFR. 2 NDE and Preserve 6 Winch Foundation 3.2.4 (Preservation) 3.2.5 (NDE) 1. Finish coat color: black (17038). 2. Areas to NDE: …- All weld joints connecting winch foundations to the deck …- Winch feet 3. Submit CFR. 3 Renew 6 Wire Rope Assembly D2.2 (Wire Rope Assemblies) Wire rope particulars: Each set is as follows: - Nominal diameter: 5/8 inch. - Nominal strength: 6x37 XXIPS IWRC RRL - Length of rope required: 150 ft per assembly - End fitting type: Poured spelter or fiege 4 Groom and Lubricate 6 Winch 3.2.6 (Groom and lubricate) 5 Final Operational Test 6 Winch B2.3 (Winches) Verify that winch and sheaves rotate freely and with no unusual noise or binding. Submit CFR. 6 Fabricate and Install 6 Label Plate B2.9 (Label plates) 4. NOTES This section is not applicable to this work item. -- 3 of 11 -- USCGC HUDSON (WLIC-160A) DOCKSIDE AVAILABILITY FY2026 40 (Rev-0) 58210_ANK_0515_IBCT REC_58210_Cpstn_IBCT_160 WLIC (ALL) (0323) WORK ITEM 9: Capstan, Inspect and Service 1. SCOPE 1.1 Intent. This work item describes the requirements for the Contractor to inspect and repair the Jered LLC Air Driven Warping Capstan, Model X-1503, located on the Fantail. 1.2 Government-furnished property. None. 2. REFERENCES COAST GUARD DRAWINGS None COAST GUARD PUBLICATIONS Coast Guard Technical Publication (TP) 4417, SWBS 582, Section A, Jan 2011, Warping Capstan Surface Forces Logistics Center Standard Specification 0000 (SFLC Std Spec 0000), 2014, General Requirements Surface Forces Logistics Center Standard Specification 5000 (SFLC Std Spec 5000), 2014, Auxiliary Machine Systems OTHER REFERENCES None 3. REQUIREMENTS 3.1 General. 3.1.1 CIR. The Contractor shall submit a CIR for the inspections listed in Table 1: • Task #1. • Task #2. • Task #3. • Task #4. -- 4 of 11 -- USCGC HUDSON (WLIC-160A) DOCKSIDE AVAILABILITY FY2026 41 (Rev-0) 3.1.2 Tech Rep. Not applicable. 3.1.3 Protective measures - general. The Contractor shall furnish and install all protective coverings to seal off and protect all non-affected vessel's components, equipment, and spaces in the vicinity of the work area against contamination during the performance of work. Upon completion of work, the Contractor shall remove all installed protective measures, inspect for the presence of contamination, and return all contaminated equipment, components, and spaces to original condition of cleanliness. 3.1.4 Interferences. The Contractor shall handle all interferences in accordance with SFLC Std Spec 0000, paragraph 3.3.5 (Interferences). Known interferences include, but are not limited to the below- listed: • Tow bitt. • . 3.2 Recurring Maintenance Requirements. The Contractor shall perform the tasks designated in Table 1 below. TABLE 1 – RECURRING MAINTENANCE REQUIREMENTS ADDITIONAL REQUIREMENTS # TASK TYPE (SFLC STD SPEC 5000 PARA. REF.) QTY COMPONENT OR ASSEMBLY APPENDIX AND PARA. FROM SFLC STD SPEC 5000 OTHER 1 Operate and Inspect 1 Warping Capstan Assembly 3.2.1 (Operate and Inspect) Appendix A Submit a CIR. 2 Disassemble, Inspect, and Preserve 1 Warping Capstan head shaft assembly 3.2.3 (Disassemble and inspect) 3.2.4 (Preservation) Submit a CIR. 3 Disassemble, Inspect, and Preserve 1 Air Motor Assembly and Associated Shaft Coupling 3.2.3 (Disassemble and inspect) 3.2.4 (Preservation) Refer to «TP» Submit a CIR. 4 Disassemble and Inspect 1 Pnuematic brake D2.3 (Brakes and clutches) Submit a CIR. 5 Disassemble, Inspect, and Preserve 1 Control Valve C2.4 (Valves and manifolds) 3.2.4 (Preservation) Submit CFR. 6 Service and Inspect 1 Gear reducer D2.4 (Open gearing and gear reducers) Submit CFR. 7 Preserve and NDE 1 Warping Capstan assembly and foundation 3.2.4 (Preservation) 3.2.5 (NDE) Submit CFR. 8 Renew All Foundation and soft patch gaskets 9 Renew 2 Pneumatic hose assembly See «TP». -- 5 of 11 -- USCGC HUDSON (WLIC-160A) DOCKSIDE AVAILABILITY FY2026 42 (Rev-0) ADDITIONAL REQUIREMENTS # TASK TYPE (SFLC STD SPEC 5000 PARA. REF.) QTY COMPONENT OR ASSEMBLY APPENDIX AND PARA. FROM SFLC STD SPEC 5000 O…