DRYDOCK: USCGC OLIVER BERRY DD FY27

Coast Guard Vessel Coatings Specifications (VCS v1.0) 1. References and TERMS/DEFINITIONS REFERENCES NAVSEA STANDARD ITEM 009-32 web link Coast GuardDrawing No. FL-2804-021 Coast Guard Drawing No. FL-2804-022 American National Standards Institute (ANSI), A118.10, 2019, Standard Specifications for Load Bearing, Bonded, Waterproof Membranes for Thin-set Ceramic Tile and Dimension Stone Installation American National Standards Institute (ANSI), A137.1, 2019 Standard Specification for Ceramic Tile ASTM International (ASTM) F1066, 2018, Tile, Floor, Vinyl Composition ASTM International (ASTM) F1700, 2020, Solid Vinyl Floor Tile Federal Specification (Fed Spec) DDD-C-95, Mar 1972, Carpets and Rugs, Wool, Nylon, Acrylic, Modacrylic MIL-A-21016, Jul 2019, Adhesive, Resilient Deck Covering MIL-A-24456, Jun 1979, Adhesive for Plastic-Vibration Damping Tile MIL-A-46106, Jun 1992, Adhesive-Sealants, Silicone, RTV, One-Component MIL-PRF-32584, Aug 2017, Deck Covering Materials, Monolithic MIL-PRF-23236, Aug 2009, Coating Systems for Ship Structures MIL-PRF-24647, Jan 2018, Paint System, Anticorrosive and Antifouling, Ship Hull MIL-PRF-24667, Mar 2018, Coating system, Non-Skid, for Roll or Spray Application MIL-DTL-15562, May 1996, Matting or Sheet, Floor Covering Insulating for High Voltage Requirements MIL-PRF-3135, Sep 2008, Deck Covering Underlay Materials MIL-PRF-32170, Jun 2006, Deck Tiles, Wear-Resistant MIL-STD-1623, Jan 2015, Fire Performance Requirements and Approved Specifications for Interior Finish Materials and Furnishings Society of Automotive Engineers (SAE) Aerospace Material Specification AMS-S-8802, 2019, Sealing Compound, Temperature-Resistant, Integral Fuel Tanks and Fuel Cell Cavities, High-Adhesion Tile Council of North America (TCNA), 2020, Handbook for Ceramic, Glass, and Stone Tile Installation The Society for Protective Coatings (SSPC) Surface Preparation Specification No.11 (SSPC-SP 11), 2012, Power Tool Cleaning to Bare Meta Terms and Definitions CUTTER Vessels of 87’ length and longer, generally sized and equiped to berth the crew onboard. BOAT Vessels of less than 87’ length, generally not equiped to berth the crew onboard. Also called “small boat”. BOOTTOP The location/placement of the boot-top shall conform to Coast GuardDrawing No. FL-2804-021 for boats and Coast Guard Drawing No. FL-2804-022 for cutters. BLACK HULLS Cutters belonging to the following cutter classes: WLB, WLM, WTGB, WLI, WLIC, WLR, WYTL, WCC. WHITE HULLS Cutters belonging to the following cutter classes: WMSL, WHEC, WMSM, WMEC, WIX, WPB, WPC, OPC, NSC . RED HULLS Cutters belonging to the following cutter classes: WAGB, WLBB, PSC Coating A layer of material applied to a surface to form a protective, decorative/cosmetic, or functional solid film after drying (or liquid film in some cases). Coating System One or more coats of one or more specified coatings. CoatingSysName This is the “coating system name” used to identify/designate a particular coating system in an SOW or PAINT SCHEDULE DWG. The CoatingSysName is defined in Section 2 AUTHORIZED COATING SYSTEMS, and maps to one or more CoatingSpecName(s). The CoatingSysName describes the number of coats required to complete the system and which CoatingSpecName(s) are authorized for use. CoatingSpecName This is the “coating specification name” used to identify/designate a particular coating specification herein. Each CoatingSpecName is defined in Section 3. COATINGS SPECIFICATIONS AND PRE-APPROVED PRODUCTS. A CoatingSpecName will map a coating specification to one or more pre-approved coating brand names that meet the specification that maps to the CoatingSpecName. FRP, FRE These are Fiber Reinforced Plastic, Fiber Reinforced Epoxy, and Fiber Reinforced Polyester; “fiberglass” hulls/components/surfaces. SEA CHEST A recess in the hull used to couple cooling water suction lines to sea water via flanges and pipe weldments. MIST COAT A mist coat is 1.0-2.0 mils (wet film thickness) of paint applied to promote adhesion or compatibility between unlike materials for spray applications only. Its a low viscosity, thin film, epoxy coating generally applied to an inorganic or organic zinc primer that penetrates the porous zinc primer and allows the occluded air to escape through the paint film prior to curing. PRESERVATION PLAN STRIPE COAT A hand-brushed, rolled, or sprayed coat of paint that is specified for a coating system, that ensures the specified coating thickness encompasses all edges, as well as at least one-inch border outside each edge, and is neat in appearance. Minimize excess thickness, as well as streaks and drops of paint. The STRIPE COAT color must contrast with the primer coat (or other coat) beneath. All corners/edges, weld joints, etc. of a surface must be STRIPE COATed. For multi-coat systems with inorganic zinc as the primer coat, apply the STRIPE COAT following the mist coat application, using the same coating used for the mist coat applied to the top of the zinc primer coat. At a minimum, and in general, a STRIPE COAT must be applied after the primer coat (or the first appropriate coat), but subsequent STRIPE COATs may be applied to achieve proper, uniform coating thickness across all surfaces. TIE COAT Similar to a MIST/TACKY COAT, except the specific tie coating material is formulated by manufacturers soley for the use in a particular coating system design. Often used in underwater hull coatings between the last AC coat and the first AF coat, or to otherwise address a chemical or other incompatibility between two coats. Sometimes called a “TACK COAT”. 2. Authorized Coating Systems AND PRE-APPROVED PRODUCTS SECTION 2 - COATING SYSTEM TABLE OF CONTENTS Coating systems are classified by System X.X Type, X.X.X Class, CoatingSysName. “Type” refers to typical surfaces/uses. “Class” refers to salient-characteristic/specific-surface, or conforms to underlying MIL S…