ELECTRODE

IDN: N4523A 6110-9800 ICN: 38LNG99229 KO: S02 KOI: 091 Any specification that is referenced in this Material Order Data sheet is required to be to the latest revision at time of award. Paragraph 6.2 Ordering Data A. MIL-DTL-21562F ELECTRODES AND RODS - WELDING, BARE, NICKEL, NICKEL ALLOY, COPPER-NICKEL ALLOY, dated 26 NOVEMBER 2024. B. Class/sub-class (see 1.2): Class 1 – Wound bare electrode (wire form): 1a – 25-pound spool weight 1b – 2-pound spool weight (furnished in 0.035 inch only) 1c – 100-pound drum weight 1d – 200-pound drum weight 1e – 300-pound drum weight 1f – 400-pound drum weight 1g – 500-pound drum weight 1h – 600-pound drum weight Other: see additional requirements 1i – 700-pound drum weight Class 2 – Cut length rods (see Table II) Type required (see Table I and Table II): MIL-EN52i Ni-Cr-Fe MIL-EN60 Ni-Cu MIL-EN61 Ni MIL-EN62 Ni-Cr-Fe MIL-EN64 Ni-Cu-A1 MIL-EN67 Cu-Ni (70-30) MIL-EN6A Ni-Cr-Fe-Ti-Mn MIL-EN82 Ni-Cr-Mn-Nb MIL-EN82H Ni-Cr-Mn-Nb MIL-EN6N Ni-Cr (80-20) MIL-E625 Ni-Cr-Mo-Nb MIL-RN52i Ni-Cr-Fe MIL-RN60 Ni-Cu MIL-RN61 Ni MIL-RN62 Ni-Cr-Fe MIL-RN64 Ni-Cu-A1 MIL-RN65 Ni-Fe-Cr-Mo-Cu MIL-RN67 Cu-Ni (70-30) MIL-RN69 Ni-Cr-Fe-Ti-A1-Nb MIL-RN6A Ni-Cr-Fe-Ti-Mn MIL-RN82 Ni-Cr-Mn-Nb MIL-RN82H Ni-Cr-Mn-Nb MIL-RN6N Ni-Cr (80-20) MIL-RN625 Ni-Cr-Mo-Nb -- 1 of 3 -- Diameter size required: 0.035-inch 0.045-inch 0.062-inch 1/16-inch 5/64-inch 3/32-inch 1/8-inch 5/32-inch 3/16-inch 1/4-inch C. Spooled electrode, drums of electrode and cut-length rods should be ordered in units as follows: Class 1a - 25 pound (wound on spool) Class 1b - 40 pounds (twenty 2-pound spools) Class 1c - 100 pounds (furnished in a drum) Class 1d - 200 pounds (furnished in a drum) Class 1e - 300 pounds (furnished in a drum) Class 1f - 400 pounds (furnished in a drum) Class 1g - 500 pounds (furnished in a drum) Class 1h - 600 pounds (furnished in a drum) Class 1i - 700 pounds (furnished in a drum) Class 2 (rods) - 5 or 10 pound Other: see additional requirements D. Specific issues of the required individual documents referenced (see 2.2.1, 2.2.2, and 2.3): Latest issue at time of award E. Minimum carbon content is not required. (see Table III, note 3) F. Maximum sulfur content is restricted to 0.007 percent. (see Table III, note 4) G. Alloy identity testing of each electrode or rod after final marking is required. (see3.3.5.2) H. Tolerances on weight for classes 1c through 1i (see 3.4.2c): See additional requirements I. Rod length required (see 3.5.2): NA - Spooled J. Plastic spool burn test is required and the sampling is required. (see 3.6 and 4.3.1.9) K. Containers are required to be in accordance with MIL-W-10430 (see 3.7.1) -- 2 of 3 -- L. Additional container requirements (see 3.7.1): Preserved and packed commercial M. Additional container marking requirements (see 3.7.3): N/A N. Percent defective samples (see 4.3.1.5 and 6.7): Acceptable quality level of 2.5 percent defective. Single sampling plan shall be used. O. Sampling for containers, container marking, and lot identification examination is not required to be in accordance with requirements other than MIL-W-10430. (see 4.3.1.8) P. Check mechanical property tolerances are not permitted for retest as part of receipt inspection (see 4.5.2.4.1.2). Q. Packaging requirements (see 4.6, 5.1, and 6.8): N/A R. Responsibility for inspection (see 6.4): per specification S. Responsibility for compliance (see 6.5): per specification T. Inspection system requirements (see 6.6): per specification Additional Requirements: Class is other, 0.045" diameter electrode, wound 8" diameter spools, the spool weight shall be 10lbs. 8" diameter spools are required to fit welding machine. All qualifications, inspections, etc. not specifically addressed in the ordering data will be accomplished per Class 1a. requirements. All unit, intermediate, and shipping containers must be marked in accordance with MIL-STD-129. Refer to DLA Procurement Note C20 for further instructions. Prepared By: BRANDON TUCKER Code: 250.1 -- 3 of 3 --