Program Depot Maintenance (PDM) Maintenance Stands.

STATEMENT OF WORK For CUI CUI Program Depot Maintenance (PDM) Stands Prepared By: 76 AMXG/MXDE 15 June 2026 -- 1 of 37 -- -- 2 of 37 -- 3 SoW Stand, 15 June 2026 CUI CUI 2. DOCUMENTATION 2.1. Specification. This SOW describes the requirements and capabilities that shall be incorporated in the new maintenance work stand set. 2.2. Additional Supporting Data. The Government will provide assembly drawings and any additional required supporting data, based on authorized and availability, not provided in this SOW documentation package, as requested by contractor within 30 calendar days after receipt of award. 2.3. References: All work and equipment provided under this solicitation shall follow good engineering practices as documented in acceptable engineering literature and shall satisfy as a minimum the following publications of the issue in effect on the date of request for proposal that form a part of this SOW. 2.3.1. American Welding Society (AWS) AWS D1.1: Structural Welding Code – Steel 2.3.2. American Society of Testing and Materials (ASTM) ASTM A36: Standard Specification for Carbon Structural Steel. 2.3.3. National Fire Protection Association (NFPA) NFPA 70-2002: National Electric Code 2.3.4. Occupational Safety and Health Administration (OSHA), including but not limited to: 29 CFR 1910 Subpart D: Walking-Working Surfaces 29 CFR 1910.23: Guarding Floor and Wall Openings and Holes 29 CFR 1910.26: Portable Metal Ladders 29 CFR 1910.27: Fixed Ladders 29 CFR 1910.28: Safety Requirements for Scaffolding 29 CFR 1910.29: Manually Propelled Mobile Ladder Stands and Scaffolds(Towers) 29 CFR 1910 Subpart N: Materials Handling and Storage 29 CFR 1910.179: Overhead and Gantry Cranes 29 CFR 1910.184: Slings 29 CFR 1926.450: Scope, Application and Definitions Applicable to Subpart L (Scaffolds) 29 CFR 1926.451: General Requirements (Scaffolds) 29 CFR 1926.452: Additional Requirements Applicable to Specific Types of Scaffolds 2.3.5. Air Force Occupational Safety and Health (AFOSH), including but not limited to: -- 3 of 37 -- 4 SoW Stand, 15 June 2026 CUI CUI AFOSH 91-5: Welding, Cutting, Brazing AFOSH 91-46: Materials Handling and Storage Equipment AFOSH 91-501: Air Force Consolidated Occupational Safety Standard: Chapter 7: Walking Surfaces, Guarding Floor and Wall Openings, Fixed Industrial Stairs, and Portable and Fixed Ladders Chapter 13: Fall Protection Chapter 16: Vehicle Mounted Elevating and Rotating Work Platforms, Manually Propelled and Self-Propelled Mobile Work Platforms, and Rolling (Mobile) Scaffolds (Towers) 2.3.6. Tinker Air Force Base Instruction (TAFBI) TAFBI 32-2001: Fire Prevention – Fire Protection Program 2.4. Order of Precedence. In the event of a conflict between the text of this SOW and the references cited herein, the text of the SOW shall take precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 2.5. Definition. Work stands or work stand sections in this SOW are defined as “Mobile Work Platforms” in AFOSH 91-501. 2.6. Reference Drawings. The following stand drawings are provided as reference: • Overall Stand Drawing Set: DAE 3203 • Pig Pen, X201961738 3. REQUIREMENTS The contractor shall provide all necessary qualified personnel, management, non- personal administrative and technical services, materials and contractor facilities in support of the requirements of this SOW. Contractors must conduct site visit(s) as necessary to gather all design requirements including dimensions before design begins. All reference drawings are for general description information. 3.1. ITEM DESCRIPTION Design, fabricate, assemble, and test fit all sets of stands as listed below, except for the Bombay Stand. See Appendix A for reference. • WS6- Wing Stand 6 (Right/Left) • NS1- Nose Stand 1 (Right/Left) • NS2- Nose Stand 2 (Right/Left) -- 4 of 37 -- 5 SoW Stand, 15 June 2026 CUI CUI • WS5- Wing Stand 5 (Right/Left) • WS7- Wing Stand 7 (Right/Left) • WS3- Wing Stand 3 (Right/Left) • WS4- Wing Stand 4 (Right/Left) • WS2- Wing Stand 2 (Right/Left) • ES2- Engine Stand 2 (Right/Left) • ES1- Engine Stand 1 (Right/Left) • FS1- Fuselage Stand 1 (Right/Left) • WS8- Wing Stand 8 (Right/Left) • WS1-Wing Stand 1 (Right/Left) • HS1- Horizontal. Stab. Stand 1 (Right/Left) • FS2- Fuselage Stand 2 (Right/Left) • HS2- Horizontal. Stab. Stand 2 (Right/Left) • Avionics Stand • Root Access Stand • Horizontal Access Stand (Right/Left) • Wing Access Stand (Right/Left) • Windshield Stand (Right/Left) • FWD Crew Access Stand • FWD Left Gear Stand • FWD Left Rear Gear Stand • AFT Gear Stand • Short AFT Landing Gear Stand • AFT Hatch Access Stand • Jack Cone Covers • Jack Gap Covers • Conect (Left/Right) • Crown (Left/Right) • Staircase (Left/Right) • Pig Pen, X201961738 3.2. DESIGN DESCRIPTION All stands must meet the following general design requirements listed below: 3.2.1. Conect/Crown/Staircase Stand; qty: 1 full set (one (1) left and one (1) right stand). See Appendix B. 3.2.1.1. Stands must be compatible with other stands sets and match existing stand configuration. 3.2.1.2. Conform to OSHA 1910 Subpart D and designed to ANSI/ASSE Z359.1 3.2.1.3. Contoured sliders with rubber bumpers flush to jet. 3.2.1.4. Removable heavy duty polyurethane casters w/ total lock. -- 5 of 37 -- 6 SoW Stand, 15 June 2026 CUI CUI 3.2.1.5. Guardrails to be aluminum. All designed to ANSI 359.1 and OSHA 1910. 3.2.1.6. Paint to match new design colors. 3.2.1.7. Slider/deck material to be aluminum and type to match existing stands. 3.2.1.8. Stairs to be modular and removable for ease of setup; design for method of easy pinning and securing to crown stand. 3.2.1.9. Stands and stairs to latch together and to the Nose Stand. 3.2.1.10. Lifting anchors for sling hoisting. 3.2.1.11. Forklift pockets for stands and stairs. 3.2.2. Pig Pen, X201961738, qty: 1. See Appendix C. 3.2.2.1. …