Playground Installation, Edward MacDowell Lake, Peterborough, NH

PLAYGROUND INSTALLATION U.S. ARMY CORPS OF ENGINEERS EDWARD MACDOWELL LAKE PETERBOROUGH, NEW HAMPSHIRE STATEMENT OF WORK Appendix B See Attached Playground Diagrams Playground Installation Instructions Swing Set Diagram Swing Set Installation Instructions -- 1 of 62 -- Capacity: 50 Age Group: 5-12 Weight: 1,350 Fall Height: 7’ FunPlay Structure Layout STR-353259 CAT # STR-353259-G 677.0 Approximate Square Feet Actual Size: 15’-4” x 23’-2” Actual Use Zone: 27’-4” x 35’-2” -- 2 of 62 -- DRAWN CHECKED SCALE PC PRIMER CONTROLLED DOCUMENT X DATE DATE SHEET 1 OF 1 USAGE REV DATE STR-353259-HL 2/25/2026 TITLE PART NO HOLE LAYOUT Company Confidential This design configuration is the property of this firm and may not be reproduced or used in any manner without the expressed written consent of LP Industries and Childforms 2/25/2026 POWDER COAT N/A N/A MA STR-353259 TOLERANCES PER ASME Y14.5. UNLESS OTHERWISE SPECIFIED STANDARD TOLERANCES = `2~ .X = `.1 X/X = `1/16 .XXX = `.062 .XX = `.06 INTERPRET DIMENSIONS AND DIMENSIONS ARE IN INCHES. REV ECO DATE BY APVD REVISION HOLE SIZE HOLE DIAMETER DEPTH A 18" 24" B 12" 18" POLE HEIGHT POLE HEIGHT 1 14' 2 11' Listed footer sizes are general recommendations. Consult your local building codes for specifics for your locations. .0 46.5 33.4 13.4 25.5 55.0 41.3 5.3 62.6 126.5 27.1 19.1 211.9 107.7 71.6 36.0 .0 31.6 4.1 29.2 6.5 47.2 56.9 26.2 10.2 B B B B B B B B B B B A2 A1 A1 A1 A1 A2 A2 A2 A2 A2 -- 3 of 62 -- I-3.5INADATRANSWSTEPINSTrevA Page 1 of 6 Childforms® FunPlay™ I-3.5INADATRANSWSTEPINST ADA Transfer Staircase Assembly Instructions:  Please read and follow all Safety Information.  Please review assembly and component Diagrams.  Verify component & hardware quantities received.  Familiarize yourself with the installation procedures. Safety  Please follow assembly procedure in the correct order.  Play site ground material should only be of an approved, shock-absorbing type and meet minimum depth requirements. NEVER install playground equipment over paved or hard surfaces.  Please be sure that all fasteners are used in the proper location.  Be sure that minimum fall zone requirements are met.  Do not allow children to play on or near equipment which is in need or repair or replacement, is incomplete or is otherwise considered unsafe. 1) Parts Inventory and Set-Up Confirm that all components, hardware and special tools are included (see Parts List). Gather any additional tools necessary for installation (hex driver, level, tape measure, etc). Please follow diagrams and instructions in order. 2) Site location and Preparation Be sure site is of adequate size- allow for minimum fall zones. Be sure site is graded, level and free of debris for proper set-up and assembly. Measure and mark site to determine structure module location and orientation. 3) Assembly- General Please use correct type and length fasteners as shown in the installation procedure. Before setting Play Structure modules in place, verify all hardware has been tightened. Be sure to follow the assembly order to ease the construction procedure. -- 4 of 62 -- I-3.5INADATRANSWSTEPINSTrevA Page 2 of 6 PARTS LIST Item Qty. Description Drawing Part Number A1 36” ADA Stairs 900-00032 A2 48” ADA Stairs 900-00038 1ea of (A1) for 36" Tall Decks 1ea of (A2) for 48" Tall Decks B (2) 36” ADA Handrail 900-00035 OR B (2) 48” ADA Handrail 900-00039 C (1) Transfer Deck w Step 900-00047-01 D (2) Access Step Handrail 900-00094 E (2) 3.5” Handrail Mounting Clamp 935-127-0004-B/G F (2) Handrail Spacer 900-00039-05 -- 5 of 62 -- I-3.5INADATRANSWSTEPINSTrevA Page 3 of 6 Hardware Components: 0-3.5INADATRANSWSTEPINST Item Qty. Description Drawing Part Number HA (6) 3/8 Neoprene Washer 100-38WSSNP HB (2) SS Flat Washer 3/8" ID x 3/4" OD 100-38WSP HB2 (24) Flat Washer 1”x.4”x.07” 100-815FW HC (8) 5/16-18 x 1 SS Torx Truss Head Bolt 100-5161 HD (4) 5/16-18 x 1-3/4 SS Torx Truss Head Bolt 100-516134 HF (14) 5/16” Stainless Nylon Lock Nut 100-516NLNSS HG (2) 5/16-18 x 1-1/4 SS Torx Truss Head Bolt 100-516114 HH (2) ¼” Hammer Drive Pin x1-1/2” 100-14HDP HI (2) 5/16-18 x 2-3/4 SS Torx Truss Head Bolt 100-516234 Tools: Item Qty. Description Drawing Part Number TB (1) Torx T-40 Driver Bit 100-00T40 -- 6 of 62 -- I-3.5INADATRANSWSTEPINSTrevA Page 4 of 6 Installation Instructions 1) Mount Staircase to Structure by taking the Staircase (A1 or A2) and mounting it to the Structure Deck using (4) 5/16-18 x 1 SS Truss Head Bolt (HC), (8) Flat Washer 1” x.4” x .07” (HB2), and (4) 5/16-18 Nylon Lock Nuts SS (HF). Be sure to prop the bottom of staircase with appropriately sized boards. (See Figure). 2) Take the handrail (B) and place (1) handrail spacer (H) between tab on the handrail leg and staircase and secure to staircase using (2) 5/16-18 x 1-3/4 SS Truss Head Bolt (HD), (2) Flat Washer 1” (HB2), (2) 5/16 Neoprene Washers (HA), and (2) 5/16-18 Nylon Lock Nuts SS (HF) per handrail. 3) Loosely mount the Clamp to support pole that the handrails will be mounting to. (See Figure). Note: The drive pin in the clamp should be facing down. HF HB2 HB2 HC HA HB2 HF HF HA HD HD -- 7 of 62 -- I-3.5INADATRANSWSTEPINSTrevA Page 5 of 6 4) Slide Mounting Bracket into clamp and then mount the bracket to the back end (threaded insert) of the handrail using (1) 5/16-18 x 1-1/4 SS Truss Head Bolt (HG) and (1) SS Flat Washer 3/8" ID x 3/4" OD (HB) per handrail. Once handrail is at desired height tighten the clamp fully to the pole. 5) Review structure spec sheet to determine the orientation of the transfer deck step. Attach the Access Step Handrail (D) to the transfer deck (C) with (2) 5/16-18 x 2.75” Bolt (HI), (2) 3/8 Neoprene Washer (HA), (2) Flat Washer 1” x.4” x.07” (HB2), and (2) 5/16-18 Nylon Lock Nuts SS (HF). 6) When mounting Transfer deck (C) to Staircase place access step handrail (D) into anchor holes and mount deck using (4) 5/16-18 x 1 SS Truss Head Bolt (HC), (8)…