Skip to content

Open for responses

Computed Topography (CT) X-Ray Cabinet Sources Sought

DEPT OF DEFENSE

Notice type
Sources Sought
Solicitation #
N68520-27-RFPREQ-KN00000-0078
NAICS
334517
PSC
6635
Set-aside
No Set aside used
Posted
November 10, 2026
Response due
November 25, 2026
Place of performance
San Diego, CA

What this opportunity is

The Department of Defense is seeking a contractor to provide a Computed Tomography (CT) system for the Fleet Readiness Center Southwest in California. This requirement is for the installation of a turn-key system to support the inspection of flight components and additive manufacturing parts. There is no set-aside for small businesses, and the notice type is Sources Sought, indicating that interested vendors should track this opportunity for potential future solicitations rather than submit bids at this stage.

Analysis by Mindy, grounded in the SAM.gov notice.

Description

SCOPE: Fleet Readiness Center Southwest (FRCSW) requires a Computed Tomography (CT) system. This new capability is necessary to support the inspection of flight components and future additive manufacturing (AM) fabricated aircraft parts and components at the FRCSW maintenance facility on board Naval Air Station (NAS) North Island in California. The contractor shall be responsible for the complete installation of all new equipment, training personnel, rigging, quality assurance, and necessary equipment to provide a turn-key system in shop KF75820, building 250 located at FRCSW North Island, CA. APPLICABLE DOCUMENTS: The documents listed in this section are cited in Sections 3.0, 4.0 and 5.0 of this specification. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all requirements of documents cited in Sections 3.0, 4.0, and 5.0, whether or not they are listed in Section 2. Unless otherwise specified, the documents listed in the solicitation or contract shall be the current edition at time of solicitation. Government Documents. Specifications, Standards, and Instructions. The following specifications, standards and instructions from a part of this document to the extent specified herein. Code of Federal Regulations (CFR) 21 CFR 1020.40: Performance Standards for Ionizing Radiation Emitting Products: Cabinet X-Ray Systems 29 CFR 1910.1096: Ionizing Radiation Safety Enablement 29 CFR 1910.147: Control of Hazardous Energy (Lockout/Tagout) 29 CFR Subpart S: Electrical Safety-Related Work Practices 29 CFR 1910.212: General Requirements for all machines 29 CFR 1910.1200: Hazardous Material Communication Department of Defense Instructions (DODI) DODI 8500.2; Information Assurance (IA) Implementation DODI 6055.08; Occupational Ionizing Radiation Protection Program (Applications for copies should be requested at www.esd.whs.mil/DD/DoD-Issuances/) Other Government Documents, Drawing, and Publications The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the documents listed in the solicitation or contract shall be the current edition at time of solicitation. LOCAL DOCUMENTS FRCSWINST 5104.2L w-CH-1 IONIZING RADIATION SAFETY PROGRAM (Distribution A) Layout Drawing Building 250 CT X-Ray Cabinet System Area Layout (Distribution A) Non-Government Publications, Specifications, Standards, and Handbooks. American Society for Testing and Materials (ASTM) ASTM E2597/E2597M - 22 Standard Practice for Manufacturing Characterization of Digital Detector Array ASTM E2737-23 Standard Practice for Digital Detector Array Performance Evaluation and Long-Term Stability ASTM E2339-20 Standard Practice for Digital Imaging and Communication in Nondestructive Evaluation (DICONDE) (Applications for copies should be addressed to ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428.) National Fire Protection Association (NFPA) NFPA 70, National Electrical Code (Applications for copies should be addressed to the National Fire Protection Association, ATTN: Support Services, 11 Tracy Drive, Avon, MA 02322) American Society of Mechanical Engineers (ASME) ASME Y14.5-2018 Dimensioning and Tolerancing ASME Y14.100 Engineering Drawing Practices (Applications for copies should be addressed to ASME International Three Park Avenue, New York, NY 10016-5990 or www.asme.org) International Organization for Standardization ISO 10303, Industrial automation systems and integration — Product data representation and exchange. Order of Precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained REQUIREMENTS: The contractor shall provide and install a complete CT system in the designated space as shown in the Layout Drawing. It is the responsibility of the contractor to get the entire unit or assembled components to the prescribed space and meet all requirements as set below as a complete system. System Capabilities: System shall meet all functions described below: Advanced 2-Dimensional X-Ray inspection 2-Dimensional CT slice visualization CT volume reconstruction for 3-Dimensional inspection 3-Dimensional internal and external surface inspection and visualization Measurement, visualization, and analysis tools X-Ray tube types and configuration shall be a dual-tube configuration consisting of a 225 kV micro-focus & 450kV mini-focus tube. The system shall have a voltage range of 20 kV – 450kV. Single-pass acquisition method for elongated objects: The system shall perform automated acquisition for elongated objects that typically do not fit in a single exposure without requiring volume stitching. The object length is only limited by the systems scanning area. This method reduces or eliminates the cone angle artifacts caused by flat, planar features common in non-spiral CT techniques. This method must support continuous scan operation. Method for expanding imagining field beyond detector panel size to cabinet size: The system shall fully scan a part that is larger than the detector panel. The system shall perform scanning in step and continuous modes while moving the detector to a series of locations to increase the scanned volume without changing the system geometry. Method of achieving resolution beyond detector panel resolution: The designed motion of the manipulator and the software shall display and analyze scan data utilizing sub-pixel analysis routines. Resolution shall be at least triple the detector’s native resolution. This method must support continuous scan operation.…

Source: SAM.gov, as posted. Verify the current solicitation before responding.

Pursue this opportunity with Mindy

See who holds it now, who else is bidding, and draft your response — grounded in real government data, not generic AI.

View the original notice on SAM.gov ↗

Open opportunities in NAICS 334517