Open for responses
Development and Optimization of Custom Pigmentation of Textiles for Artemis Suit Materials Project Phase IV
NATIONAL AERONAUTICS AND SPACE ADMINISTRATION
Notice type
Special Notice
Solicitation #
80NSSC27949350Q
NAICS
334516
PSC
6640
Posted
November 16, 2026
Response due
November 18, 2026
Place of performance
Houston, TX
Description
`Statement of Work for Pigmented Coating Pilot
Request for quotation | Artemis Suit Materials project | Revision A | 5 October 2026
The contractor shall quote a pilot application and evaluation of a flexible white pigmented coating on Government-
provided textiles. The work will produce documented, representative coated material for adhesion and handling
assessment and for subsequent Government-led environmental testing. This SOW defines a base effort and
separately priced options so quantities and cost can be adjusted after sample layout is agreed.
1 Technical basis and objective
Preliminary trials of a flexible white pigmented coating on seven textiles showed encouraging tape adhesion and
manual bend performance after a single spray session with IPA wipe cleaning and no primer. Minor bubbling
occurred on one side of a laminated PTFE construction. These observations are preliminary and shall be
documented and evaluated on larger specimens under this pilot.
The pilot shall determine whether the coating can be applied reproducibly, survive cutting, sewing and
representative folding or rolling, maintain adhesion after bakeout, and provide suitable specimens for cryogenic,
abrasion, UV, and material qualification assessments. No dust barrier or flight qualification is assumed from this
effort.
2 Government furnished materials and sample plan
The Government will provide identified fabric lots with face and back orientation marked, where applicable. The
initial seven candidates are listed below; the Government may substitute an equivalent candidate before quote
acceptance without increasing the count. The contractor shall propose the usable coated sheet dimensions
needed to yield the planned specimens, separate cutting-trial samples and witness samples, with allowance for
spray margins and cutting losses. Identify additional usable reserve area and its price in the quotation to support
repeat tests, added test opportunities, and future exposure specimens such as MISSE.
Candidate Material or construction
1 Woven basalt textile, with existing mineral oil finish
2 Versive BetaCloth
3 PTFE fabric laminated with fluoropolymer film (identified as FEP
in the earlier list; confirm construction)
4 JPS Kevlar 775
5 Custom Vectran/Kevlar weave; limited supply
6 Teflon T162 plain weave
7 Vectran Turtleskin Style 1410
The Government will also provide clean PTFE film sheets or strips for optional coating or coating-on-substrate
outgassing specimens. The exact material IDs, lot sizes, coating face orientation, and graphic candidates shall be
recorded at kickoff.
3 Base scope of work
Task 1 Plan and receive materials. The contractor shall review the specimen schedule with the Government,
document incoming condition, and agree on usable coated sheet dimensions. The contractor will coat large pieces,
and JSC will cut test specimens as needed. Provide representative coated offcuts or small samples from each
textile for cutting trials. The objective is to establish one repeatable cutting method applicable across the textiles
that minimizes fiber fraying and foreign object debris (FOD). The contractor shall document candidate methods and
edge condition, and JSC will evaluate their suitability for routine specimen preparation. Report any textile requiring a
different method. No substitution of primer or surface treatment shall occur without Government approval.
-- 1 of 4 --
Task 2 Coat the textiles. Clean the seven textiles using an IPA wipe and apply flexible white pigmented coating to
both sides in a single spray session. Multiple passes within that session are permitted as required by the application
process. Spray pass or coat count may be retained in internal process notes but shall not be a specified acceptance
or quality control requirement. Record material identity, sides coated, cleaning agent, application method, coating
formulation or batch, cure or dry conditions, and coating usage or dry add-on and thickness where measurable.
Room-temperature curing is acceptable under the applicable coating procedure. Manually record the laboratory
temperature and relative humidity, application and cure dates, and elapsed cure time before handling or testing; a
continuous cure chart is not required. Photograph representative surfaces and any bubbles, penetration, or other
anomalies. Keep a small uncoated control from each material where sufficient stock permits.
Task 3 Prepare and return coated sheets. Supply large coated pieces for JSC to cut, together with the agreed
cutting-trial and witness samples. Identify usable dimensions, orientation, material lot and coated faces on each
piece or its packaging. Package with suitable release material or separation to prevent unintended sticking or
surface damage during shipment. The specimen schedule below is a planning basis for the minimum usable coated
area, not a requirement for the contractor to deliver individual precut coupons. Provide the three Kevlar tumbler
panels through sufficient usable sheet area to yield three 15 × 7 in panels. Agree on reduced allocations for scarce
fabric and separately identify reserve area in the quote.
Use Planned JSC specimen yield per material Test lead
Thermal cycling and roll handling 2 at 12 × 2 in Government
LN2 crack and hard crease 2 at 8 × 8 in Government
Sewing, air permeability, mass, thickness,
reserve 6 at 5 × 5 in Government
Cryogenic Scott crease flex 2 at 1 × 5 in Government
Rotary tumbler abrasion and dust
resistance with lunar simulant 3 at 15 × 7 in, Kevlar only Government
Task 4 Document adhesion and handling. On representative witness coupons for each substrate and each coated
face, perform and photograph tape pulls using a specified tape and consistent procedure. Report the tape, dwell
and removal conditions, coating transfer, substrate damage, and bubbling. Assess cut edges, moderate and tight
rolling, and folding. Coating-to-coating blocking means adhesion or sticking between coated surfaces held …
Source: SAM.gov, as posted. Verify the current solicitation before responding.
Pursue this opportunity with Mindy
See who holds it now, who else is bidding, and draft your response — grounded in real government data, not generic AI.
View the original notice on SAM.gov ↗Open opportunities in NAICS 334516
Field of Testing
DEPT OF DEFENSE · Special Notice · due December 2, 2026
6630--Automated Gram Stainer System for VA Pittsburgh Healthcare System
VETERANS AFFAIRS, DEPARTMENT OF · Sources Sought · due November 24, 2026
Combined Synopsis Solicitation (competitive)
HEALTH AND HUMAN SERVICES, DEPARTMENT OF · Combined Synopsis/Solicitation · due December 4, 2026
6640--Next Generation Sequencing (NGS) Reagent Kits
VETERANS AFFAIRS, DEPARTMENT OF · Sources Sought · due November 22, 2026
EGauge Combo Model 4540 Asphalt & Soil Density Gauge
DEPT OF DEFENSE · Special Notice · due November 19, 2026
6515--Notice of Intent Sole Source - Labs - Purchase ofOne (1) QuantStudio 3 (QS3) qPCR System, One (1) iBright FL1500 Imaging System, and associated manufacturer-compatible consumables for Oklahoma City VA Medical Center (OKCVAMC)
VETERANS AFFAIRS, DEPARTMENT OF · Special Notice · due November 25, 2026