Open for responses
Utility Tractor Replacement
AGRICULTURE, DEPARTMENT OF
Notice type
Solicitation
Solicitation #
12444127Q0005
NAICS
333924
PSC
2420
Set-aside
Small Business Set Aside - Total
Posted
November 17, 2026
Response due
November 25, 2026
Place of performance
New Ellenton, SC
Description
Page 1 of 7
US Department of Agriculture (USDA)
Specifications statement: “Purchase of a utility tractor to be
used on the Enoree Ranger District for use on various forest
projects; wildlife opening planting, roadside mowing, and
storm recovery efforts.”
Specific specifications on pages 2-7
-- 1 of 7 --
Page 2 of 7
Deliverables / Specifications
4x4 WHEELED UTILITY TRACTOR REQUIREMENTS. The Contractor shall provide the following new, current year, 4x4 Wheeled
Utility Tractor with attachments that meets or exceeds the following specifications:
Item 1 – 4x4 WHEELED UTILITY TRACTOR MANDATORY SPECIFICATIONS
Motor Minimum 120 Engine HP, Diesel
Transmission
PowerQuad PLUS 16F/16R
Drive Mechanical Front Wheel Drive (MFWD) w/turnable fenders:
Wheels 3Rear Wheel Size(19.5L-24in)10PR R4 BIAS, Front Wheel Size (12.5/80-
18in)6PR I3 R4 Type
Safety
Closed Operator station- Shall meet OSHA and Federal safety
requirements and equipment standards in appendix A. Certified Roll
Over Protection Structure (ROPS) shall be in accordance with 29CFR1926
and 30CFR56.14130. The certified ROPS will have a certification label on
the unit or in the operator manual.
Hydraulics
Mechanical center link w/ball ends Cat2; Greater than 93 l/min
hydraulic pump. Rear remote hydraulic connecters,
Hydraulic Pump Pressure (min): Steering/1958 psi, implement/2856 psi
Electrical
System 12 volt
PTO Drive Three Speed PTO 540/540E/1000
Hitch
3 Point Hitch; left hand adjustable lift link; Rear left fender
hitch control; Draft links with Cat 2 telescopic ball end, category
2 center link, sway control blocks; rear lift capacity 5,150lbs
REQUIRED ADDITIONAL ITEMS
Hydraulic 3 mechanical stackable rear valves; 3 stackable mid SCV with mechanical
Joystick controls;
Required to fit attachments: Rotatory cutter FC5012; Front End Loader H310 NSL
-- 2 of 7 --
Page 3 of 7
Delivery to address below: USFS, Savannah River Site, 1 Mile Inside Aiken
Barricade, New Ellenton SC 29809 Contact POC to coordinate delivery to a
SECURE site.
POC: Michael Morris, ph: 803-457-3489
email: michael.c.morris@usda.gov
-- 3 of 7 --
Page 4 of 7
Appendix A— Equipment Standards
Reference Content
29CFR1910.266 (f)(3) 1910.266(f)(3)(ii)(B)
Each machine manufactured after August 1, 1996, shall have ROPS tested, installed, and
maintained in accordance with the Society of Automotive Engineers SAE J1040, April 1988,
"Performance Criteria for Rollover Protective Structures (ROPS) for Construction, Earthmoving,
Forestry, and Mining Machines", which is incorporated by reference as specified in § 1910.6.
1910.266(f)(3)(ii)(C)
This incorporation by reference was approved by the Director of the Federal Register in
accordance with 5 U.S.C. 552(a) and 1 CFR part 51. Copies may be obtained from the Society
of Automotive Engineers, 400 Commonwealth Drive, Warrendale, PA 15096. Copies may be
inspected at the Docket Office, Occupational Safety and Health Administration, U.S. Department
of Labor, 200 Constitution Avenue NW., room N2625, Washington, DC 20210, or at the National
Archives and Records Administration (NARA). For information on the availability of this material
at NARA, call 202-741-6030, or go to:
http://www.archives.gov/federal_register/code_of_federal_regulations/ibr_locations.html.
1910.266(f)(3)(iii)
FOPS shall be installed, tested and maintained in accordance with the Society of Automotive
Engineers SAE J231, January 1981, "Minimum Performance Criteria for Falling Object
Protective Structures (FOPS)", which is incorporated by reference as specified in § 1910.6.
1910.266(f)(3)(iv)
ROPS and FOPS shall meet the requirements of the Society of Automotive Engineers SAE
J397, April 1988, "Deflection Limiting Volume-ROPS/FOPS Laboratory Evaluation", which is
incorporated by reference as specified in § 1910.6.
1910.266(f)(3)(v)
Each protective structure shall be of a size that does not impede the operator's normal
movements.
1910.266(f)(3)(vi)
The overhead covering of each cab shall be of solid material and shall extend over the entire
canopy.
1910.266(f)(3)(vii)
Each machine manufactured after August 1, 1996, shall have a cab that is fully enclosed with
mesh material with openings no greater than 2 inches (5.08 cm) at its least dimension. The cab
may be enclosed with other material(s) where the employer demonstrates such material(s)
provides equivalent protection and visibility. Exception: Equivalent visibility is not required for the
lower portion of the cab where there are control panels or similar obstructions in the cab, or
where visibility is not necessary for safe operation of the machine.
1910.266(f)(3)(viii)
Each machine manufactured on or before August 1, 1996 shall have a cab which meets the
requirements specified in paragraph (f)(3)(vii) or a protective canopy for the operator which
meets the following requirements:
1910.266(f)(3)(viii)(A)
The protective canopy shall be constructed to protect the operator from injury due to falling
trees, limbs, saplings or branches which might enter the compartment side areas and from
snapping winch lines or other objects;
1910.266(f)(3)(viii)(B)
The lower portion of the cab shall be fully enclosed with solid material, except at entrances, to
prevent the operator from being injured from obstacles entering the cab;
1910.266(f)(3)(viii)(C)
The upper rear portion of the cab shall be fully enclosed with open mesh material with openings
of such size as to reject the entrance of an object larger than 2 inches in diameter. It shall
provide maximum rearward visibility; and
-- 4 of 7 --
Page 5 of 7
1910.266(f)(3)(viii)(D)
Open mesh shall be extended forward as far as possible from the rear corners of the cab sides
so as to give the maximum protection against obstacles, branches, etc., entering the cab area.
1910.266(f)(3)(ix)
The enclosure of the upper portion of each cab shall allow maximum visibility.
1910.266(f)(3)(x)
When transparent material is used to enclose the upper portion of the cab, it shall be made of
safety glass or ot…
Source: SAM.gov, as posted. Verify the current solicitation before responding.
Pursue this opportunity with Mindy
See who holds it now, who else is bidding, and draft your response — grounded in real government data, not generic AI.
View the original notice on SAM.gov ↗Open opportunities in NAICS 333924
Utility Tractor Replacement
AGRICULTURE, DEPARTMENT OF · Solicitation · due November 25, 2026
Utility Tractor Replacement
AGRICULTURE, DEPARTMENT OF · Solicitation · due November 25, 2026
INDUSTRY DAY 2026 FA8534-2X-R-XXXX
DEPT OF DEFENSE · Special Notice · due December 2, 2026
93--GLASS,SAFETY,SINGLE PL
DEPT OF DEFENSE · Combined Synopsis/Solicitation · due November 23, 2026
39--TRUCK,HAND
DEPT OF DEFENSE · Combined Synopsis/Solicitation · due November 23, 2026
39--BINDER,LOAD
DEPT OF DEFENSE · Combined Synopsis/Solicitation · due November 20, 2026