Gate Motor Replacement for Kisatchie National Forest, LA

COMMERCIAL DC VEHICULAR SLIDE GATE OPERATOR INSTALLATION MANUAL • THIS PRODUCT MUST BE INSTALLED AND SERVICED IN ACCORDANCE WITH THIS MANUAL BY A TRAINED GATE SYSTEMS TECHNICIAN ONLY. • This model is for use on vehicular passage gates ONLY and not intended for use on pedestrian passage gates. • This model is intended for use in Class I, II, III and IV vehicular slide gate applications. • Visit LiftMaster.com to locate a professional installing dealer in your area. • This gate operator is compatible with MyQ® and Security+ 2.0® accessories. LiftMaster 300 Windsor Drive Oak Brook, IL 60523 Access installation and technical support guides or register this product Send it in by texting the photo to 71403. Take a photo of the camera icon including the points ( ). 1. 2. Model CSL24UL EXTERNAL SAFETY DEVICES REQUIRED. SEE SAFETY SECTION FOR UL 325 ENTRAPMENT PROTECTION REQUIREMENTS CSL24ULTECH -- 1 of 60 -- 2 2 2 3 3 4 4 4 5 6 6 7 8 9 9 10 11 12 14 16 16 18 20 22 23 24 24 25 26 26 28 28 SAFETY Safety Symbol and Signal Word Review Usage Class UL325 Entrapment Protection Requirements Safety Installation Information Role of Dealers, Installers, and Trained Gate System Technicians Role of End Users/Home Owners Gate Construction Information INTRODUCTION Carton Inventory Operator Specifications Site Preparation INSTALLATION Types of Installations Step 1 Determine Location for Operator Step 2 Install the Operator Step 3 Attach the Chain Step 4 Install Entrapment Protection Step 5 Earth Ground Rod Step 6 Power Wiring Step 7 Connect Batteries Step 8 Dual Gate Setup Step 9 Install the Cover Step 10 Install Warning Signs ADJUSTMENT Limit and Force Adjustment Obstruction Test PROGRAMMING Remote Controls (Not Provided) OPERATION Gate Operator Setup Examples Control Board Overview 29 30 30 30 30 31 31 32 32 33 33 34 35 36 36 37 37 38 38 39 41 42 45 45 49 49 50 51 52 53 55 Manual Disconnect Reset Switch Operator Alarm Remote Control ACCESSORY WIRING External Control Devices Locks Miscellaneous Wiring EXPANSION BOARD Expansion Board Overview Auxiliary Relay 1 and 2 Wiring Accessories to the Expansion Board MAINTENANCE Maintenance Chart Batteries Drive Train TROUBLESHOOTING Diagnostic Codes Diagnostic Codes Table Control Board LEDs Troubleshooting Chart APPENDIX Solar Panel(s) SAMS Wiring with Relays Not Energized Dual Gate Settings Limit Setup with a Remote Control WIRING DIAGRAM REPAIR PARTS ACCESSORIES WARRANTY SAFETY CHECKLIST 56 TABLE OF CONTENTS SAFETY Safety Symbol and Signal Word Review These Safety Symbols and Signal Words on the following pages will alert you to the possibility of Serious Injury or Death if you do not comply with the warnings that accompany them. The hazard may come from something mechanical or from electric shock. Read the warnings carefully. MECHANICAL ELECTRICAL When you see this Signal Word on the following pages, it will alert you to the possibility of damage to your gate and/or the gate operator if you do not comply with the cautionary statements that accompany it. Read them carefully. IMPORTANT NOTE: • BEFORE attempting to install, operate or maintain the operator, you must read and fully understand this manual and follow all safety instructions. • DO NOT attempt repair or service of your gate operator unless you are an Authorized Gate Systems Technician. WARNING: This product can expose you to chemicals including lead, which are known to the State of California to cause cancer or birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov -- 2 of 60 -- 3 Usage Class Class I - Residential Vehicular Gate Operator A vehicular gate operator (or system) intended for use in garages or parking areas associated with a residence of one-to four single families. Class II - Commercial/General Access Vehicular Gate A vehicular gate operator (or system) intended for use in a commercial location or building such as a multi-family housing unit (five or more single family units), hotel, garages, retail store, or other buildings accessible by or servicing the general public. Class III - Industrial/Limited Access Vehicular Gate A vehicular gate operator (or system) intended for use in an industrial location or building such as a factory or loading dock area or other locations not accessible by or intended to service the general public. Class IV - Restricted Access Vehicular Gate Operator A vehicular gate operator (or system) intended for use in a guarded industrial location or building such as an airport security area or other restricted access locations not servicing the general public, in which unauthorized access is prevented via supervision by security personnel. SAFETY UL325 Entrapment Protection Requirements Definitions ENTRAPMENT: The condition when a person is caught or held in a position that increases the risk of injury. SLIDE GATE ENTRAPMENT ZONE: An entrapment zone exists if at any point during travel, the gap between the gate and any opposing fixed edge or surface such as posts, walls, pillars, columns or the operator itself, is less than 16" (406 mm) in a location up to 6 ft. (1.8 m) above grade. INDEPENDENT MONITORED ENTRAPMENT PROTECTION DEVICE: An entrapment protection device is independent if it is a different type (photoelectric sensors, edge device, inherent protection device) from the other devices in the same entrapment zone. Use the Site Planning Safety Checklist in the appendix to identify entrapment zones found in your installation. Requirements • A minimum of two independent monitored entrapment protection devices are required to be installed at each entrapment zone. • It is the responsibility of the installer to install external monitored entrapment protection devices for each entrapment zone. • The operator will only operate with a minimum of two independent monitored entrapment protection devices installed in each direction; two in the open direction and two in the closed direction. Acceptable entrapment protection device types i…