Description
PR # 61200PR2700055532
STATEMENT OF WORK
LAST UPDATED: 11/13/2026
STATEMENT OF WORK (SOW)
FOR
Steadman Fire Alarm Panel Repair
1.0 GENERAL
1.1 BACKGROUND
U.S. Coast Guard (USCG) Training Center (TRACEN) Petaluma located at 599 Tomales Road
Petaluma; CA 94952 is the Coast Guard’s largest West Coast Training Center. Our graduates
are the latest chefs, medics, storekeepers, yeoman, information systems technicians,
electronics technicians, operations specialists, and aviation survival technicians (AST). We are
also home to the Coast Guard Leadership Development Center’s Chief Petty Officer Academy.
1.2 SCOPE
The requirement of this contract is for the contractor to furnish all labor, qualified personnel,
tools, materials, equipment, supplies, services, and other items necessary to troubleshoot and
correct an ongoing fire-alarm ground-fault condition on the Siemens XLS FireFinder at USCG
TRACEN Petaluma.
1.3 OBJECTIVE
The Contractor shall furnish all supervision, qualified personnel, diagnostic equipment, tools,
materials, transportation, and incidentals required to troubleshoot, trace, repair, and fully restore
the affected fire-alarm field circuit to normal operating condition, eliminating the active ground-
fault condition on the Siemens FireFinder-XLS system at the U.S. Coast Guard (USCG)
Training Center (TRACEN) Petaluma, located at 599 Tomales Road, Petaluma, CA 94952.
1.4 APPLICABLE DOCUMENTS
1.4.1 Reference Documents
The following documents may be helpful to the Contractor in performing the work described in
this document:
• NFPA 72 (National Fire Alarm and Signaling Code)
• NFPA 70 (National Electrical Code - NEC)
2.0 SPECIFIC REQUIREMENTS/TASKS
2.1 TASK ONE. FIRE-ALARM PANEL TROUBLESHOOTING AND DIAGNOSTICS
• Diagnose and correct the ongoing fire-alarm ground fault panel condition on the
Siemens XLS FireFinder.
• Inspect the fire-alarm control panel, associated power supplies, batteries, modules,
wiring terminations, and connected field circuits as necessary to identify the source of
the fault condition.
2.2 TASK TWO. FIELD-CIRCUIT TESTING AND REPAIR
• Trace, test, and isolate the affected fire-alarm field wiring and devices to identify the
location and cause of the issue.
• Repair, replace, reconnect, or re-terminate defective field wiring, connections, or related
components necessary to restore the affected circuit to proper operation.
-- 1 of 5 --
PR # 61200PR2700055532
STATEMENT OF WORK
LAST UPDATED: 11/13/2026
• Furnish sufficient compatible fire-alarm wiring and associated repair materials to
complete corrective repairs during the service visit if the fault is confirmed in the field
wiring.
2.3 TASK THREE. FIRE-ALARM PANEL REPAIR AND RESTORATION
• Repair or replace defective fire-alarm panel components, modules, terminals, power-
supply components, or related equipment as required to eliminate the identified trouble
condition.
• Restore the fire-alarm control panel and affected circuit to normal operating condition
upon completion of repairs.
• Perform all required panel resets, functional checks, and verification testing following
repair activities.
2.4 TASK FOUR. SYSTEM MONITORING AND COORDINATION
• Maintain appropriate monitoring of the fire-alarm control panel throughout
troubleshooting and repair activities to minimize disruption to the facility fire-alarm
system.
• Coordinate all required alarm impairments, testing activities, resets, and restoration
actions with designated USCG TRACEN Petaluma personnel.
• Immediately notify the Government representative of any condition that cannot be
corrected during the service visit or that requires additional materials, labor, or follow-on
repairs.
2.5 TASK FIVE. FUNCTIONAL TESTING AND DOCUMENTATION
• Verify that the repaired fire-alarm panel and affected field circuit are free of the identified
ground-fault condition and operate normally upon completion of repairs.
• Conduct functional testing of repaired components and associated circuits to confirm
proper system operation.
• Provide a written service report identifying the reported condition, troubleshooting
performed, findings, repairs completed, materials used, test results, and any
recommended follow-on actions.
2.6 TASK SIX. FINAL SYSTEM STATUS AND CLOSEOUT
• Return the fire-alarm control panel and affected systems to normal operating status at
the conclusion of the service visit.
• Ensure all work areas are cleaned and all debris, removed components, packaging, and
unused materials are removed from Government property.
• Provide the Government representative with final notification that the system has been
restored or document any remaining deficiencies requiring additional corrective action.
2.7 TASK SEVEN. WARRANTY
• Contractor shall include a one-year warranty for all work performed.
3.0 CONTRACTOR PERSONNEL
3.1 QUALIFIED PERSONNEL
The Contractor shall provide qualified personnel holding a NICET Level 2 certification or C10
certification.
-- 2 of 5 --
PR # 61200PR2700055532
STATEMENT OF WORK
LAST UPDATED: 11/13/2026
3.1.1 NICET Level 2 Certification Requirements:
• A minimum of 2 years of fire detection and signaling systems experience.
• Must include at least 12 months of fire alarm systems experience (including alarm and
detection, notification, sprinkler monitoring, and interfaces/controls for agent releasing
• suppression systems) in roles such as installation, inspection, testing, commissioning,
technical system estimating/sales, or plan preparation/maintenance.
3.1.2 C-10 Electrical Contractor License (California):
• Requires 4 years of journeyman-level experience in electrical work within the past 10
years, verifiable through documentation.
• C-10 holders can legally perform low-voltage systems work (equivalent to C-7 work),
residential/commercial/industrial wiring, solar PV systems, EV charging stations, panel
upgrades, and generator installations.
• Limitations: Cannot perform fire protection system installation/servicing that requir…
Source: SAM.gov, as posted. Verify the current solicitation before responding.