What this opportunity is
The Department of Defense is seeking maintenance, repair, and preservation services for the YON-325 vessel, as indicated in a Sources Sought notice. This opportunity falls under NAICS 336611 and is suitable for small businesses with expertise in marine vessel maintenance. Interested vendors should note that this is a Sources Sought notice, which is primarily for market research purposes, meaning that tracking this opportunity is essential, but it may not lead directly to a bid submission at this stage.
Analysis by Mindy, grounded in the SAM.gov notice.
Description
1
YON-325
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
COVER SHEET – STATEMENT OF WORK (SOW)
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
N4523A27Q1004
SOLICITATION COPY
REV A 10/02/2026
Version: One Date Prepared: 08/04/2026
24 June 2008
-- 1 of 79 --
2
Table of Contents
Paragraph / Section Page Number
1.0 General Requirements
1.1 Vessel Characteristics 4
1.2 Scope Overview 4/5
1.3 Definitions 5/7
1.4 Arrival Conference 7
1.5 Required Documents 7/8
1.6 Progress Meetings 8/9
1.7 Availability Requirements 9/14
1.8 Care of Vessel 14/15
1.9 Workmanship 15/16
1.10 Corrective Action Request (CAR) 16/17
1.11 Condition Found/Inspection Discrepancy Report
(CFR/IDR)
18/20
1.12 Interferences 20
1.13 Safety Requirements 20/21
1.14 Hot Work/Welding 22/23
1.15 Threaded Fasteners 23
1.16 Preservation 23/25
1.17 Environmental and Hazardous Waste
Management
27
1.18 Materials 27
1.19 Weight Control 27-28
1.20 Label Plates 28
1.21 Integrated Logistic Support 28
1.22 Gas Free 28-29
1.23 General Requirements for Testing 29/33
1.24 Process Control Procedure (PCP) Requirements 34
1.25 Compartment Arrival / Closeout Inspections 35
1.26 Technical Representative 35/37
1.27 Heavy Weather Plan 40
1.28 Foreign Material Exclusion 41
-- 2 of 79 --
3
2.0 References
2.1 Order of Precedence 42
2.2 Discrepancies 42
Consolidated List of References 43/45
3.0 Work Requirements
3.1 Docking and Undocking 45/50
3.2 Hull Repairs 50/56
3.3 Structural Repairs 56-57
3.4 Tanks/Voids 57/64
3.5 Main Deck Repairs 64/66
3.6 Superstructure 66/68
3.7 Main Propulsion Repairs 68
3.8 Steering System Repairs 68
3.9 Machinery Systems 68/71
3.10 Electrical Systems 71
3.11 Piping Repairs 72/75
3.12 Weight Handling Systems 75
3.13 Dock and Sea Trials 76
4.0 Government Furnished Material (GFM) 76
w5.0 Data Submission List 77/79
Statement of Work (SOW)
-- 3 of 79 --
4
1.0 General Requirements: This document invokes the requirements applicable
to the docking and maintenance work to be performed on One each YON-321
class vessel. Work performed and accomplished shall be in accordance with the
highest quality workmanship standards and practices commonly accepted in the
commercial marine industry and the technical references listed herein. The
Contractor is responsible for understanding and complying with all requirements
specified herein. The requirements listed herein work in conjunction with the
technical drawings and other references to describe the essential features,
functions, and requirements of the work performed.
1.1 Vessel Characteristics:
FUEL OIL BARGE (YON-325) Built by Sundial Marine
Construction &
Repair, INC.
Length: 199 FT Draft: 3 FT
Width: 54 FT Full Displacement: 2848 L Tons
Height: 15 FT Light Load 706 L Tons
Hull Type: Steel Age: 21 years
1.2 Scope Overview: Coordinate with the Contracting Officer, via the
Contracting Officer’s Representative (COR) to deliver the vessel from
Manchester Fuel Depot to the Contractor’s facility. Dock, wash, and clean
exterior surfaces of the vessel upon docking. Replace zinc anodes on hull /
Skegs. Accomplish preservation to Underwater Hull, Freeboard, Main deck,
Deck house, Cargo piping and all deck fittings. Clean non-skid located Main
deck, Deck house top and Cargo deck. Remove, clean and install Rubber
fenders. Modify existing Piping eliminate Aft Flow Meter and insert spool.
Accomplish Ultrasonic test measurement and visual inspection of the hull, Main
deck, Cargo deck and Deck house top. Open, Clean, Pump and maintain clean
and dry each tank/void. Inspect tanks/voids for defects Refresh Exhaust Muffler
for Yanmar and Main Engine. Replace Solar Panels. Remove Antenna Support
Modification. Replace Fuel Oil Tank Piping. Replace and Calibrate Cargo Tank
Level Indicator’s (TLI’s). Perform Preliminary Air test of Tanks/voids/Steel
Fendering and Skegs. Accomplish a final closure inspection of each tank/void
upon completion of all work installing new gaskets and fasteners. Perform Final
Air Test of Tanks/voids/Steel Fendering and Skegs. Accomplish repair, replace
gaskets, and adjust watertight hatches and doors. Accomplish Cargo Pump Diesel
and Diesel generator maintenance and repair. Undock the vessel. Arrange and
-- 4 of 79 --
5
coordinate the delivery of the vessel back to the Government with the
Contracting Officer via the COR. Calibration of TLI’s, shall be conducted at
Manchester Fuel Depot (MFD) in Manchester, WA
1.3 Definitions: As used throughout this Specification, the following definitions
and terms have meanings as indicated:
1.3.1 Unless otherwise stated, “as shown”, “as indicated”, “as detailed”, or
other words of similar import refer to the contractual documents including
reference documents and publications.
1.3.2 The words “as directed”, “as approved”, “when authorized” or words
of similar import refer to the direction, requirements, permission, approval, or
acceptance by the Contracting Officer.
1.3.3 The term “Objective Quality Evidence” (OQE) shall mean current,
accurate, and complete objective documentation and information submitted
together as a complete data package sufficient that a qualified and disinterested
third party could analyze and evaluate whether technical requirements were
achieved.
1.3.4 Where “in accordance with regulatory body requirements” is stated,
the industrial efforts shall be in accordance with the appropriate commercial
regulatory body requirements unless otherwise authorized by the Government.
1.3.5 The term “marine” or “marine quality” means an item constructed of
materials unaffected by moisture, sea spray, extremes in temperature or other
hazards of the marine environment and designed and constructed to perform its
intended functions under marine operating conditions.
1.3.6 The term “herein” means the applicable section(s) of this
Specification.
1.3.7 The term “NAVSEA” means the Naval Sea Systems Command, one …
Source: SAM.gov, as posted. Verify the current solicitation before responding.